How Do Diamond Blades Work?

SCIENCE! and Technology Articles on Desert Diamond Industries' BlogSo you have a diamond blade, it cuts stuff, and it cuts it well. That’s good enough for most people. Are you one of those rare and troublesome folk, though, who’s wondered how it works? If you are, then this article was written for you.

We’ve tackled this topic before, but we want to focus on it a bit more today. First, let’s talk about how most diamond blades work.

How Most Diamond Blades Work: Most diamond blades have cutting segments that are made up of diamond grit suspended in some kind of metal matrix or “bond”. Some of these diamonds are on the surface, but most are buried within the cutting segment’s bond.

It’s important to remember two things about these surface diamonds. First, they grind instead of cut, an important distinction that we’ll get back to in a moment. Second, they do all the cutting work on your blade. All the bond does is hold these surface diamonds in place, while the diamonds buried within the bond do, well, nothing.

Now, diamonds are one of the hardest substances on Earth (they lost the top spot in 2009 to two other materials), but even they’ll wear down and stop cutting on a diamond blade.

This is where the bond comes into play. Ideally, the bond will wear away just fast enough to shed worn surface diamonds and expose fresh, sharp diamonds buried deeper in the cutting segment. This means that you shouldn’t notice any change in your cutting speed as your blade wears down.

Problems with Most Diamond Blades: Of course, nothing happens “ideally”. Your blade bond won’t exactly match the materials that you cut. It will either be too soft or too hard.

If your bond is too soft, your blade will wear down faster than normal. This means that you’ll have to replace your blade more often, which in turn means that you’ll spend more than you should on replacement diamond blades.

If your bond is too hard, on the other hand, the surface diamonds – the diamonds that do all of your blade’s cutting – will wear down faster than the bond. This can lead to your blade “glazing over”, where the surface diamonds wear down completely before they can be shed. When this happens, your blade will cut slower and then refuse to cut.

Worn and glazed blades are both dangerous, and for similar reasons.

Soft-bonded blades can have their cutting segments “undercut” in abrasive materials, like asphalt, green concrete, and sandstone, especially if they don’t have undercut protection. Glazed blades, on the other hand, hammer the material instead of cutting it, which increases friction and overheats the welds holding the cutting segments. Undercutting and overheating can both break cutting segments off the blade, injuring or even killing the saw operator.

To avoid broken segments, you should, as a rule of thumb, choose harder bonds when cutting softer materials and softer bonds when cutting harder materials. This isn’t a perfect rule, though, and could force you to change blades whenever you change the material that you’re cutting.

Advantages of Vacuum-Brazed Blades: Vacuum-brazed blades like the Ductile Iron Safety Blade and Fire Rescue Safety Blade avoid these problems because they have their diamonds vacuum-brazed onto the surfaces of their cutting segments. None of the diamonds are buried inside a bond. Instead, they’re all on the surface, ready to cut.

This means that you don’t have to match up the bond of a vacuum-brazed blade to the hardness of your material. Vacuum-brazed blades cut almost everything, including metals, asphalt, stone, and concrete, and are more versatile than other diamond blades.

Remember, we’ll be at the Tri-State Seminar On-The-River here in beautiful Las Vegas, NV from Sept. 24 to Sept. 26! Visit us in Booth 1222 at the South Point Convention Center. See our press release for details.

Works Cited

“Our Vacuum Brazing Process Gives You a More Versatile Blade That Can Tackle Any Cutting Job.” Desert Diamond Industries Product Catalog. N.p.: n.p., n.d. 27. Print.

“Frequently Asked Questions.” Desert Diamond Industries. Desert Diamond Industries, n.d. Web. 27 Aug. 2013. < >.

“Frequently Asked Questions – Why Is My Diamond Blade’s Bond Important? How Does It Affect What I Can Cut and My Cutting Speed?” Desert Diamond Industries’ Blog. Desert Diamond Industries, 12 Dec. 2012. Web. 27 Aug. 2013. < >.

“Q. My diamond blade isn’t cutting. Is it defective?” Desert Diamond Industries’ Blog. Desert Diamond Industries, 29 Nov. 2012. Web. 27 Aug. 2013. < >.

2 thoughts on “How Do Diamond Blades Work?

  1. Pingback: How Do Grinding Wheels Work? | Desert Diamond Industries Blog

  2. Pingback: When Do You Replace a Worn Out Diamond Blade? | Desert Diamond Industries Blog

Leave a Reply

Please log in using one of these methods to post your comment: Logo

You are commenting using your account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )


Connecting to %s