Monthly Archives: May 2014

How to Cut Safely with a Diamond Blade and Handheld Saw

How to Cut Safely with a Diamond Blade and Handheld SawTo get ready for the ACE14 conference and for all the guys who get stuck down in the trenches cutting pipe, we’d like to offer this article on how to use diamond blades and handheld saws safely. It includes things what you should check before you start cutting and what you should do while you’re cutting. Follow them and stay safe!

Remember to visit us near the tapping competitions in Booth 2466 (PDF) at the ACE14 conference in Boston, MA from June 8 to 11! 

Before Cutting

  • Make sure that you’re well-rested. You’ll hold the saw closer to your body if you’re tired, which will increase your chances of injury if your saw kicks back.
  • Make sure you’re trained in how to hold and cut with your saw properly and safely.
  • If anyone’s helping you, make sure that they’re properly trained and know how to assist you properly.
  • Wear proper safety gear, including safety glasses and footwear, headgear, and eye and hearing protection. Avoid wearing anything that could get caught in the blade, like jewelry or loose clothes.
  • When cutting brick, block, stone, or concrete, use a respirator. It’ll protect you against lung diseases like lung cancer, silicosis, and pneumoconiosis.
  • Only cut materials recommended by your blade’s manufacturer. Using your blade on improper materials can endanger your safety and cause excessive blade wear and damage.
  • Don’t mount your blade on a saw that doesn’t meet the minimum requirements set by the blade’s manufacturer.
  • Don’t mount your blade on any type of machine other than those recommended by the blade’s manufacturer.
  • Don’t dry-cut unless your blade is specifically designed for dry-cutting. Dry-cutting with a wet-cutting blade can weaken the welds holding the blade’s cutting segments and endanger your safety.
  • Don’t use a wet-cutting blade without sufficient water. If you do, you’ll weaken the blade’s welds and endanger your safety.
  • When cutting with a wet-cutting blade, make sure that the blade has an adequate and continuous flow of water. Neither gravity feeds nor the “booster pumps” on your saw will supply enough water to a wet-cutting blade.
  • Make sure you feed the right amount of water to your blade. Too much water can cause blade polishing, while too little can turn the cuttings into a paste that can jam or bind your blade and cause kickback.
  • Use segmented blades instead of toothed blades. If you must use toothed blades, make sure that they have enough “tooth set”, or room between the sides of the blade and the sides of your cut, to prevent binding and kickback.
  • Never mount your blade on a saw with a higher RPM than that recommended by the blade’s manufacturer.
  • Make sure your blade is the right size for your saw and job.
  • Inspect your blade for damage, even if it’s new. Look for cracked segments or cores, missing or damaged segments, undercutting under the segments, warped cores, and damaged or out-of-round arbors. If you find any of these or any other kind of damage, the blade is unsafe to use. Throw it away.
  • Make sure your blade doesn’t have foreign or abrasive material on its sides. These can increase your blade’s thickness and friction during cutting, which can lead to binding and kickback.
  • Make sure the blade’s arbor hole is the right size for your saw’s shaft and is mounted between proper flanges. Don’t try to force it onto an undersized shaft, as this can endanger your safety and cause excessive blade wear. Don’t try to alter the size of the arbor hole.
  • Make sure the blade is properly supported on your saw’s shaft and doesn’t slip or wobble.
  • Don’t use an arbor hole bushing if you’re going to mount your blade on a high-speed saw.
  • Make sure your saw is in good working order, is safe, and complies with all safety requirements.
  • Make sure that your saw’s shaft bearings don’t have end or radial play.
  • Set your saw’s lead-off adjustment so that the blade will travel straight.
  • Check your saw’s pulley for excessive wear.
  • Tighten the V-belts on your saw if they need it.
  • Make sure the flanges are properly assembled, in place, of equal or proper diameter, don’t show excessive wear, and are clean and flat.
  • Make sure your blade is mounted correctly on your saw and spins in the right direction.
  • Hand-tighten the blade to your saw with a wrench that’s no more than 8″ long. Don’t tighten the mounting nut too much.
  • Make sure your saw’s blade guards are in place, undamaged, and properly secured. Don’t try to pull or tie them back or otherwise defeat them.
  • Check all the fluids in your saw.
  • Make sure you have enough room to make your cut safely. If you have to, establish a safe zone.
  • Make sure that the material that you’re going to cut is supported so that it won’t sag. This will prevent the material from pinching your blade, which can cause kickback.
  • Make sure that you’re aware of all hazards both before and during your cut.
  • Set your cutting depth to no more than 1/4″ greater than the thickness of what you’re cutting. Doing so will prevent your blade from contacting foreign objects once you cut through and will prevent kickback.
  • Don’t use a saw that’s too heavy for you to control.

During Cutting

  • Hold your saw firmly with both hands.
  • Don’t stand directly in line with your blade when starting your saw or during cutting. This will reduce your chances of being injured if your saw kicks back.
  • Before starting your cut, free-run your saw to make sure that it operates smoothly.
  • Make sure you can properly rest the saw’s shoe on the clamped, supported portion of your material before cutting.
  • Let the blade spin up to full speed before starting your cut.
  • If you’re re-entering a cut, align your blade first, then ease it into the cut to prevent binding and kickback.
  • Maintain your balance and footing at all times. Never cut on a stepstool or ladder or cut in an awkward position. Mount the saw on guide tracks if you have to cut above your shoulders.
  • Don’t lean into your cuts. If you lean in to your cuts, your body will be closer to your saw, which will increase your chances of being injured if your saw kicks back.
  • Don’t force your blade into your material. Your blade should be able to bite into your material and then continue cutting with nothing more than the weight of your saw. Forcing the blade can cause overheating, binding, or blade damage.
  • Take your time. Cut with a slow sawing or reciprocating motion.
  • Don’t cut or let anything touch the upper front quadrant of your blade. This will prevent kickback.
  • Use greater care when cutting material with foreign objects in it, like reinforced concrete. Your saw can kick back when the blade encounters these objects.
  • Don’t try to make your cuts in one pass, especially with dry-cutting blades. Use several passes until you reach your desired cutting depth.
  • Never let your blade overheat. Remove dry-cutting blades periodically and let them free-run to air-cool.
  • Don’t exceed the blade’s maximum RPM while cutting.
  • Make sure the material doesn’t roll, slip, or vibrate. These can all bind the blade and cause kickback.
  • Don’t grind with the sides of your blade unless your blade is designed for grinding.
  • Don’t pry or push material with your blade.
  • Make only straight cuts. Never twist, turn, or deflect your blade in the cut or make off-center, crooked, curved, or radii cuts.
  • Avoid long-term, repetitive cutting, which can tire you out. When you’re tired, you’ll hold the saw closer to your body, which will increase your chances of being injured if it kicks back.
  • Take your finger off the trigger or power switch after making a partial cut, if your blade binds up, if your saw stalls, or if power is interrupted.
  • Allow cut-off pieces to fall away to prevent binding and kickback.
  • Ease up on the saw near the end of your cut. This will prevent the blade from hitting the floor or foreign objects and prevent kickback.
  • After you finish your cut, keep your blade in the cut until it comes to a full stop.

Works Cited

Daily, Sean D. “From the Archives: How Do I Prevent Chainsaw Kickback and Circular Saw Kickback?” Desert Diamond Industries Blog. Desert Diamond Industries, 6 Dec. 2013. Web. 28 May 2014. < https://desertdiamondindustries.wordpress.com/2013/12/06/frequently-asked-questions-how-do-i-prevent-saw-kickback/ >.

Daily, Sean D. “Safe Dry-Cutting with Diamond Blades.” Desert Diamond Industries Blog. Desert Diamond Industries, 5 Mar. 2014. Web. 28 May 2014. < https://desertdiamondindustries.wordpress.com/2014/03/05/safe-dry-cutting-with-diamond-blades/ >.

“How Diamond Blades Work.” How Diamond Blades Work. Norton Construction Products, n.d. Web. 28 May 2014. < http://www.nortonconstructionproducts.com/application/diamond-blades.aspx >.

“Pavingexpert and Pulvex – Cutting with Diamond Blades.” Pavingexpert and Pulvex – Cutting with Diamond Blades. Pulvex, n.d. Web. 28 May 2014. < http://www.pavingexpert.com/diamond_blades_01.htm >.

“Safety Tips When Dry Cutting With Diamond Blades.” Safety Tips When Dry Cutting With Diamond Blades. ChinShine Diamond Tools Co., Ltd., n.d. Web. 28 May 2014. < http://www.diamond-blade.org/technical-article/2013/1116/110.html#.U4XoqfldV8E >.

“Wet Cutting – Diamond Blades.” Wet Cutting – Diamond Blades. Norton Construction Products, n.d. Web. 28 May 2014. < http://www.nortonconstructionproducts.com/solutions/wet-cutting.aspx >.

“I Have Never Used a Blade that Worked as Efficient as This Blade” – Houston Fire Department ARFF

"I Have Never Used a Blade that Worked as Efficient as This Blade" - Houston Fire Department ARFFForgive us, but we have to toot our own horn today.

Senior Captain Ronald Krusleski of the Houston Fire Department‘s Aircraft Rescue Firefighting (ARFF) squad sent us a glowing testimonial for the Fire Rescue Safety Blade yesterday. We’re rightly proud of some of the things that he said:

“We used the 16” Safety Blade on a Boeing 727 fuselage during a four day rescue class. This blade was unbelievable on how quick it cut through the fuselage. We used one blade for a day and part of another day before we changed to a new blade. In the past, we would have gone through multiple blades in one day. I have been in the fire service for 28 years and I have never used a blade that worked as efficient (sic) as this blade. We will be ordering more blades to replace the few we used during our training.” (emphasis ours)

Well, Capt. Krusleski, we’d like to thank you for the kind words and the photo that you took of the Fire Rescue Safety Blade during training:

Houston Airport Fire Rescue Squads Using Fire Rescue Safety Blade on Boeing 727

Find out more about the Fire Rescue Safety Blade today!

Press Release – Manufacturer of Ductile Iron Safety Blades to Exhibit at ACE14 Conference in Boston, MA

See You at the American Water Works Association's ACE14!

Courtesy of American Water Works Association

Desert Diamond Industries
2799 E. Tropicana Avenue
Suite G
Las Vegas, NV 89121
Contact: Nicholas Mione or Gionni Mione
Phone: (800) 654-5890 or (702) 606-6631
E-mail: ddi@desertdiamondindustries.com
Website: http://desertdiamondindustries.com/
Blog: https://desertdiamondindustries.wordpress.com/
FOR IMMEDIATE RELEASE

LAS VEGAS, NV, May 14, 2014 – Desert Diamond Industries (DDI) will make its third appearance at the American Water Works Association‘s ACE conference from June 8 to 11. They will be in Booth 2466 (PDF) at the Boston Convention & Exhibition Center in Boston, MA.

Among the DDI products to be shown at the ACE14 conference are the company’s full line of Safety Blades – including the Ductile Iron Safety Blade and Ductile Iron Ring Saw Safety Blade – as well as a wide range of concrete blades, Husqvarna cut-off saws, and ICS chain saws. DDI will also raffle off a new Ductile Iron Safety Blade and every day and a free Husqvarna K970 ring saw and Ductile Iron Ring Saw Safety Blade on the convention’s final day.

When asked about his company’s third appearance at ACE, DDI founder and president Nicholas Mione said, “Oh, it’s going to be great. We’ve never been to the East Coast before for a water show, and we’ll be able to introduce water companies there to the safest and most effective blade for cutting pipe.” He added that their appearance at ACE was “staying true to our mission to make pipe repair easier and job sites safer for the guys in the field.”

Founded in Las Vegas, NV in 2008 by Nicholas Mione and Gionni Mione, DDI is now the largest supplier of diamond blades to governmental agencies in the United States and Canada. Up to 90 percent of water and underground utilities, fire departments, and foundries in these two countries use DDI’s signature Ductile Iron Safety Blade and Fire Rescue Safety Blade.

Download a PDF copy of this press release.

How to Prevent Deaths from Trench Collapses, by NIOSH

We’ve published articles about preventing trench collapse deaths before (like here and here). What we haven’t done, though, is cover this subject in any kind of detail.

To rectify that, we’d like to offer this article by the National Institute for Occupational Safety and Health (NIOSH). It covers what you can do both before and during a job to prevent trench collapses and keep yourself and your workers safe.

NIOSH, “Preventing Worker Deaths from Trench Cave-ins” (PDF)

Going to the ACE14 conference in Boston, MA? So are we! We’ll be there from June 8 to 11! Visit us in Booth 2466 (PDF) near the tapping competitions!